A shape is classed a "Bar Size Shape" when its greatest dimension (length excluded) is less than 3 inches.

The shapes listed in this section conform to ASTM A 36, a standard specification for structural steel.

ASTM Specification A 36

Stocked Lengths 20' , 30', & 40' as indicated

It is a "Structural Shape" when at least one of its dimensions (length excluded) is 3 inches or greater.

The shapes listed in this section conform to ASTM A 36, a standard specification for structural steel.

ASTM Specification A 36

Stocked in Lengths up to 60'

Structural Shapes

Listed on the following pages are shapes commonly carried in stock. The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. In the column headed "AISI Designation", a letter or letters precedes the size and weight per foot. For example, C3 X 4.1 is the AISI designation for a 3" x 4.1# Standard Structural Channel.

"W" shapes are doubly-symmetric wide flange shapes used as beams or columns whose inside flange surfaces are substantially parallel. A shape having essentially the same nominal weight and dimensions as a "W" shape listed in the tabulation but whose inside flange surfaces are not parallel may also be considered a "W" shape having the same nomenclature as the tabulated shape, provided its average flange thickness is essentially the same shape as the flange thickness of the "W" shape.

"S" shapes are doubly-symmetric shapes produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard beam shapes. The essential part of these standards is that the inside flange surfaces of American Standard beam shapes have approximately a 16 2/3% slope.

"M" shapes are doubly-symmetric shapes that cannot be classified as "W", "S", or bearing pile shapes. (Although not included in the standard nomenclature tabulation, bearing piles are doubly-symmetric wide flange shapes whose inside flange surfaces are essentially parallel and whose flange and web have essentially the same thickness.)

"C" shapes are channels produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard channels. The essential part of these standards is that the inside flange surfaces of American Standard channels have approximately a 16 2/3% slope.

"MC" shapes are channels that cannot be classified as "C" shapes.

Stock Lengths 20' and 30'

Structural Shapes

Listed on the following pages are shapes commonly carried in stock. The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. In the column headed "AISI Designation", a letter or letters precedes the size and weight per foot. For example, C3 X 4.1 is the AISI designation for a 3" x 4.1# Standard Structural Channel.

"W" shapes are doubly-symmetric wide flange shapes used as beams or columns whose inside flange surfaces are substantially parallel. A shape having essentially the same nominal weight and dimensions as a "W" shape listed in the tabulation but whose inside flange surfaces are not parallel may also be considered a "W" shape having the same nomenclature as the tabulated shape, provided its average flange thickness is essentially the same shape as the flange thickness of the "W" shape.

"S" shapes are doubly-symmetric shapes produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard beam shapes. The essential part of these standards is that the inside flange surfaces of American Standard beam shapes have approximately a 16 2/3% slope.

"M" shapes are doubly-symmetric shapes that cannot be classified as "W", "S", or bearing pile shapes. (Although not included in the standard nomenclature tabulation, bearing piles are doubly-symmetric wide flange shapes whose inside flange surfaces are essentially parallel and whose flange and web have essentially the same thickness.)

"C" shapes are channels produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard channels. The essential part of these standards is that the inside flange surfaces of American Standard channels have approximately a 16 2/3% slope.

"MC" shapes are channels that cannot be classified as "C" shapes.

Stocked in Lengths up to 60'

Structural Shapes

Listed on the following pages are shapes commonly carried in stock. The American Iron and Steel Institute has established a designation system for structural shapes, which has been adopted by steel producers. In the column headed "AISI Designation", a letter or letters precedes the size and weight per foot. For example, C3 X 4.1 is the AISI designation for a 3" x 4.1# Standard Structural Channel.

"W" shapes are doubly-symmetric wide flange shapes used as beams or columns whose inside flange surfaces are substantially parallel. A shape having essentially the same nominal weight and dimensions as a "W" shape listed in the tabulation but whose inside flange surfaces are not parallel may also be considered a "W" shape having the same nomenclature as the tabulated shape, provided its average flange thickness is essentially the same shape as the flange thickness of the "W" shape.

"S" shapes are doubly-symmetric shapes produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard beam shapes. The essential part of these standards is that the inside flange surfaces of American Standard beam shapes have approximately a 16 2/3% slope.

"M" shapes are doubly-symmetric shapes that cannot be classified as "W", "S", or bearing pile shapes. (Although not included in the standard nomenclature tabulation, bearing piles are doubly-symmetric wide flange shapes whose inside flange surfaces are essentially parallel and whose flange and web have essentially the same thickness.)

"C" shapes are channels produced in accordance with dimensional standards adopted in 1896 by the Association of American Steel Manufacturers for American Standard channels. The essential part of these standards is that the inside flange surfaces of American Standard channels have approximately a 16 2/3% slope.

"MC" shapes are channels that cannot be classified as "C" shapes.

Stocked in Lengths up to 60'